# Spiral stair calculator

> 5′ spiral stair, 9′ rise: 11 treads (9″ rises), a 5′ kit (26″ clear path) and a floor opening of ≥ 62″. A spiral or modular stair kit sized to your floor-to-floor height and opening — or what a fabricated steel stair involves — with the code checks for width, rise and headroom.

## What to buy (5′ spiral stair, 9′ rise)

Every line shows the quantity to buy and how StudSheet got it: the spacing, the waste and the package size, so you can check it before the supply house or the quote.

| Buy | Material | How StudSheet counts it | What it is for |
|---|---|---|---|
| **1 kit** | Spiral stair kit, 60″ diameter (60″ diameter, 102″–114″ floor to floor) | 11 treads and the top platform, 9″ rises, about 26″ of clear path. Kits run about $2,300 for 42″ and $3,300–3,900 for 60″ (Home Depot listings, Oct 2026); other sizes are estimates. | Center column, treads with spacers, balusters, a handrail and the top platform, set to your floor-to-floor height. Wide enough (26″ of clear path or more) for a main stair where the code allows a spiral. |
| **4 anchors** | ⅜″ wedge anchors (stainless outdoors) (⅜″ zinc-plated) | 4 through the base plate, set to the depth on the box. The kit’s instructions may ask another size: use theirs. | Four per base plate in concrete, set at least 4″ from the slab edge and to the depth on the box. |
| **8 lag screws** | ⅜″ structural lag screws (galvanized or stainless) (⅜″ × 4″) | The top platform into the header and joists. The kit’s instructions may ask another size: use theirs. | Through a base plate or bracket into solid blocking. Where you can reach behind, through-bolts are stronger. |

### In Canada (1.52 m spiral stair, 2.74 m rise)

Set to Canada, the Sheet works the job out again for Ontario: metric sizes, bag sizes, the frost depth and the code notes. It doesn't just convert feet to meters. The first lines:

- **1 kit, Spiral stair kit, 1.52 m diameter:** 11 treads and the top platform, 229 mm rises, about 660 mm of clear path.
- **4 anchors, 10 mm wedge anchors (stainless outdoors):** 4 through the base plate, set to the depth on the box. The kit’s instructions may ask another size: use theirs.
- **8 lag screws, 10 mm structural lag screws (galvanized or stainless):** The top platform into the header and joists. The kit’s instructions may ask another size: use theirs.

## The steps, in order

> **PRO STEP: most of it is DIY-friendly; one step needs a licensed pro.** About 9–15 hours of work for this example.

1. Order the kit for your height: measure from the finished floor to the finished floor and the opening, and check both against the kit’s range first.
2. Mark the center: plumb down from the opening’s layout point to the floor; check the opening clears the stair by 1″ all round.
3. Anchor the base plate: wedge anchors into the concrete.
4. Stack the treads and spacers on the column as the instructions say, setting each rise to 9″; leave the bolts loose.
5. Fasten the top platform to the header and joists; plumb the column; fan the treads to the layout and tighten every bolt.
6. Install the balusters and the handrail (34–38″), then the well rail around the floor opening.
7. Check every tread for level and every opening with a 4″ ball.

## Tools (15)

Must-have tools first, then the ones that help and the ones to rent for the day.

| Tool | Need | Why |
|---|---|---|
| **4-ft level** | **Must have** | Every tread level, front to back and side to side |
| **6-ft level** | **Must have** | Plumbs the column on two faces |
| **Plumb bob** | **Must have** | Drops the center from the opening to the floor |
| **Cross-line laser level** | Good to have | Faster than the plumb bob for the center and the heights |
| **Tape measure (25 ft)** | **Must have** | The red boxes every 16″ on the blade are stud spacing. |
| **Carpenter's pencil** | **Must have** | Flat, doesn't roll away, marks rough lumber. |
| **Cordless drill/driver** | **Must have** | Pilot holes for the lags |
| **Impact driver** | **Must have** | Drives the lags |
| **Socket and ratchet set** | **Must have** | Tightens the column and tread bolts |
| **Hammer drill + masonry bit** | Rent | Drills the concrete for the anchors |
| **Clamps (2)** | Good to have | Holds the platform while you fasten it |
| **Step ladder (6 ft)** | **Must have** | Reaching the treads and the top platform |
| **Safety glasses** | **Must have** | Every cut, every nail, every time. |
| **Work gloves** | **Must have** | Tack strip, block and lumber shred hands. |
| **Hard hat** | Good to have | Working under the opening |

## Mistakes and how the math works

### Mistakes that cost a callback or a second trip

- **Ordering before measuring:** Kits are made for a range of floor-to-floor heights: measure from finished floor to finished floor (carpet, tile and all) before you order.
- **An opening too small for the stair:** The stair needs the opening 2″ bigger than its diameter, or heads hit the floor’s edge. Cutting it bigger later is structural work.
- **A narrow spiral as the only stair to bedrooms:** A 42″ or 48″ spiral is too narrow for the code’s main stair: it’s a second way up.
- **A column out of plumb:** Every tread follows the column: plumb it on two faces before you tighten anything.
- **No guard around the floor opening:** The open sides of the hole are a fall of a full storey: guard them before anyone uses the upper floor.

### What the calculator assumes

- Spiral stairs (IRC R311.7.10.1; R318.7 in the 2024 IRC): 26″ clear at and below the handrail, 6¾″ treads at the walkline, rises ≤ 9½″, headroom 6′ 6″. Clear path by kit: 42″ → 17″, 60″ → 26″ (Mylen); 48″, 64″ and 72″ estimated.
- Headroom is a rough check: the floor above 11-1/4″ thick at the opening.
- Guards around the opening 36″ high; the well rail is counted as about 2½ sides of the opening.
- Anchors as typical kit instructions ask (⅜″); follow the kit’s list where it differs.

## Code, permits and safety

The Sheet sets its code notes for the job's state or province. These are New Jersey's and Ontario's; the [code reference](https://studsheet.com/codes) has more. Always confirm with your building department.

- **Two people and a careful layout:** A spiral kit goes together on its center column: one person holds, one bolts, and the column has to stand dead plumb or every tread is off. Plan a day for two.
- **A stock kit fits:** Kits are sold by floor-to-floor height: yours (108″) fits the 102″–114″ kit. Re-measure from the finished floor to the finished floor before you order.
- **A guard around the floor opening:** Every open side of the opening needs a guard 36″ high with openings under 4″ (IRC R312.1; R321.1 in the 2024 IRC). Kits sell a matching well rail.
- **Permit likely needed:** A new stair between floors usually needs a permit: it’s structural, and a way out of the upper floor. Ask your town’s construction office before you buy a kit.
- **Spiral stairs in Canada:** The National Building Code has no spiral-stair article for houses (BCBC 9.8.4.7 is reserved): spiral stairs need your municipality’s OK, usually only as a second stair. Confirm with your building department.

## Questions

### What materials do I need to install a spiral or steel stair?

For the worked example, a 5′ spiral stair, 9′ rise, the Sheet counts 3 lines with waste included, starting with spiral stair kit, 60″ diameter (1 kit), ⅜″ wedge anchors (stainless outdoors) (4 anchors), ⅜″ structural lag screws (galvanized or stainless) (8 lag screws). Each line's math is in the table above. Put in your own sizes in the [steel stairs calculator](https://app.studsheet.com/p/steelstairs) and every line is counted again.

### How long does it take to install a spiral or steel stair, and can I do it myself?

About 9 to 15 hours for the worked example, in 7 steps. StudSheet stamps it **PRO STEP**: dIY with a pro for one step.

### What tools do I need to install a spiral or steel stair?

15 in all. The must-haves start with 4-ft level, 6-ft level, plumb bob, tape measure (25 ft), carpenter's pencil, cordless drill/driver. On the Sheet you mark each one as owned, to buy or to rent.

## Ask about it

Stuck while you install a spiral or steel stair? Ask in the [Steel and spiral stairs group](https://studsheet.com/forum/steel-and-spiral-stairs) of the StudSheet community with this Sheet attached. Homeowners who've done it and verified pros answer, and anyone can read it.

## More metal & glass Sheets

- **[Iron and metal railings for contractors](https://studsheet.com/trades/railings)**: run this takeoff at your own prices, send the estimate, and get it signed and the deposit paid.
- **[All 45 Sheets](https://studsheet.com/sheets)**, across 16 trades.
- **[Code reference](https://studsheet.com/codes):** frost depths, guard heights, stairs, retaining walls.